Compressor washing is the routine that reverses most of this loss. This guide explains how fouling develops, the difference between online and offline washing, what water and cleaning agents are needed and how to set wash intervals from data rather than habit. It also covers what to include when specifying a new turbine and how washing fits around the redundancy of a data center plant.
What fouling costs
Fouling has its largest effect on the front stages of the compressor, where the blades are larger and first meet the incoming air. As deposits build, air flow and pressure ratio fall, and the turbine must burn more fuel for each megawatt delivered. Output losses of a few percent between washes are common in dusty or industrial locations, with a matching rise in heat rate.
For a plant serving a data center, those percentages matter twice. They reduce the capacity available to cover the campus load, which affects the reserve margin, and they raise fuel cost on every hour of operation. Our lifecycle cost comparison shows how efficiency losses add up over the life of a unit.
Filtration comes first
Washing treats the symptom; filtration reduces the cause. A well chosen inlet system with weather protection, coalescers where moisture is an issue and high efficiency final filters cuts fouling rates considerably. The right filter class depends on the site: desert dust, coastal salt and industrial pollution each call for different arrangements.
Filter differential pressure should be trended alongside compressor performance. Sudden improvement in filter pressure drop can mean a damaged element letting dirt through, which would show up soon after as faster fouling. The inlet filtration scope sets out what to specify for a new unit.
Online washing at load
Online washing sprays a fine mist of demineralised water, sometimes with a cleaning agent approved by the turbine manufacturer, into the compressor inlet while the unit runs at or near full load. It removes loose and soft deposits from the early stages and slows the rate of performance loss between offline washes. It does not require a shutdown, which is its main attraction.
Online washing has limits. Water quantity and droplet size are controlled tightly to avoid erosion, so the cleaning effect is modest and mostly limited to the front stages. Some manufacturers restrict online washing at low ambient temperatures because of icing risk. The wash frequency for online washing is often daily or weekly, depending on site conditions and supplier guidance.
Offline crank washing
Offline washing is done with the unit shut down and cooled. The starter turns the rotor at cranking speed while wash solution is injected, allowed to soak and then rinsed out with clean water, followed by a drying run. Because the solution reaches further into the compressor and contact time is longer, offline washing restores much more of the lost performance than online washing.
The cost is downtime, typically several hours including cool down, washing, rinsing and drying. Many operators combine offline washes with other planned work, such as filter changes or inspections, so the outage serves more than one purpose. Our page on inspection intervals explains how those windows are usually planned.
Water, cleaning agents and drains
Wash water quality is critical. Dissolved minerals and sodium left on blades can cause corrosion in the hot section, so manufacturers specify demineralised water with limits on conductivity, total dissolved solids and specific contaminants. A wash skid with storage, pumps, heating for offline washes and metering is normally part of the package or the balance of plant.
Cleaning agents must be approved by the turbine supplier, mixed at the stated ratio and fully rinsed. Waste water from offline washes contains removed deposits and detergent, so it needs collection through drains to a holding tank and disposal according to local environmental rules. Planning that route at the design stage avoids improvised hoses and spills later.
Setting intervals from data
Fixed calendar intervals are simple but often wrong. A better method trends corrected output, heat rate and compressor discharge pressure, then schedules an offline wash when losses pass a threshold where the cost of lost output and extra fuel exceeds the cost of the outage. Comparing performance before and after each wash also shows how much loss is recoverable and how much reflects permanent wear.
When washes stop restoring performance, the cause is probably not fouling. Hard deposits, blade erosion or increased clearances may need a borescope inspection or a hand clean during a major outage.
What to specify and how to schedule it
When buying a new turbine, confirm that online and offline wash systems are included, the nozzle arrangement suits the compressor, the wash skid capacity matches the number of units and the water treatment supply is in scope. Drain collection, controls integration and operator training belong in the same list, along with the wash procedures the manufacturer expects to see followed for warranty purposes.
On an N+1 data center plant, offline washes can be rotated so only one unit is out at a time while the others carry the load. That rotation should sit within the O&M plan and be coordinated with the campus, so washes never coincide with high load periods or other planned outages.
About the authors
This guide comes from the USP&E gas turbine performance and maintenance engineering team. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. How turbines are applied to campus loads is explained in our article on turbine plants for data centers.
Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.
Compressor washing questions
What is a gas turbine compressor wash?
Cleaning deposits off compressor blades with demineralised water and approved cleaning agents to recover lost output and efficiency.
What is the difference between online and offline washing?
Online washing runs at load without a shutdown and removes light deposits; offline washing is done while cranking a cooled unit and restores much more performance.
How often should a compressor be washed?
Online washes often run daily or weekly. Offline wash timing should be set from corrected performance trends and site conditions.
Why must wash water be demineralised?
Minerals and sodium left on blades can cause hot section corrosion, so manufacturers set strict water quality limits.
Does washing replace good inlet filtration?
No. Filtration reduces fouling at source; washing removes what the filters miss.
What if a wash no longer restores output?
The loss is likely from erosion, hard deposits or wear, which calls for a borescope inspection rather than more washing.
Review your wash strategy
Send the turbine model, site conditions and recent performance data, and our engineers will suggest wash methods, intervals and the equipment needed.
If a document set is easier than a conversation, send it to info@uspeglobal.com or upload a summary through the turbine performance enquiry; to talk it over, dial +27 10 822 2324. Current new and used units are shown in our gas turbine inventory.
